Today I am going to show you how we removed the large builder mirror in our master bathroom. Our large bathroom mirror was attached (with glue) to the wall, so it was extra challenging to remove. Here is the technique we found to safely detach it from the wall so we could replace it with more decorative smaller mirrors.
I am mid-makeover for our master bathroom. The state of it has been pretty bad ever since we moved into our new home. We’ve slowly been overhauling each room in our builder-basic home and major projects like our kitchen and our more public rooms like our library and dining room have gotten the immediate attention. While our master bedroom is still in need of its refresh, our bathroom has been sorely neglected down to the paper blinds on the window and blah, white tile, stainless fixtures and plain jane paint.
So while we like to do full “ta-da!” type reveals, this post is still mid-project {edit: see the finished space HERE}. Since I had to do some research as to the safest and easiest way to take down the huge, eight-foot mirror you see above, I thought it was worth sharing how I did it. I had found two pretty, smaller mirrors at HomeGoods and couldn’t wait to get them put up in place of this monstrosity. {If for some reason you can’t remove your mirror, we also have a great renter-friendly way to update a large mirror HERE.}
HOW TO REMOVE A LARGE BATHROOM MIRROR
FROM THE WALL
I started by taping up the mirror and protecting our counter with a bedspread, I figured if the mirror did fall it would help contain the glass. To jump ahead briefly, we successful removed the entire mirror with no cracking or breaking and we’ll be able to repurpose it in our basement for a work-out area, but it’s better to be safe than sorry with this much glass. I also don’t think this is a one person job, the mirror was exceptionally heavy, so be sure you have help close by if you attempt this project.
Once I removed the few plastic clips that held it to the wall, my hopes of it coming off easily were crushed, it was clearly glued to the wall in multiple places. I went to the internet to see if I could find any tricks to remove it and read about using a hair dryer to soften the glue, then using a large wire to saw downward to separate the glue from the back of the mirror.
Luckily, I have a Wagner Heat Gun, which was a great solution but in the end we found with such a huge expanse of wall there really wasn’t a good way of knowing exactly where the glue was. This method would work really well on a smaller mirror.
We then ran a long piece of strong picture wire behind the mirror, both of us holding an end and pulling downward with all our might, sometimes using a sawing motion in an attempt to make better progress. We got about halfway down and could feel the mirror start to separate from the wall but unfortunately, that was as far as we got. My husband then began to gently pry the mirror from the wall using screwdrivers and other flat objects, every once and awhile we’d feel another pop as another piece of glue separated from the wall.
Once we were able to pull the top part forward, I used another handy household tool, my Steam Machine, and using the smallest nozzle blasted the hot steam between the wall and the mirror. Since we knew that we were going to have major drywall to repair, I didn’t think the small amount of moisture would create too much of a problem, and I knew it would soften the glue or the drywall enough to let the mirror separate. Shortly after a little bit of steam, we heard almost a “pop” when the mirror gave way, and yes there may have been a few cheers at that point!
Note: I haven’t personally used this but another option is a hand-held steam machine such as this one.
After it was removed, we assessed the damage. I had several places that needed drywall patches and quite a bit of sparkling/repair work ahead. {Note: I used these mesh patches over the largest holes and they worked well.}
Once we popped off the bottom metal track that the mirror had set in {which was also glued on-argh!} still having my SteamMachine on hand, I used it to blast away all the grime, glue and gunk that had accumulated under the mirror.
I also used the Heat Gun to melt all the remaining glue on the wall, then sanded it off before I started patching it up.
After all the patching and sanding was done, I went ahead and rehung the mirrors for instant gratification {and so I could see to put my make-up on the next day!}.
You can still see the damage under the mirror, and on the wall, but ignore that and look at the pretty mirrors, they are available here.
Another similar option is here.
Here is a pinnable graphic if you would like to save this post.
I did another small update in the room a few months later, you can see more of that HERE.
Sources: chair | window blind | frames with mats
If you are looking for more bathroom inspiration, here are a few other spaces we have designed.
Elegant Master Bathroom Renovation
Vintage Powder Room Renovation
Small Guest Bathroom with Wallpaper
Tour the new home we built HERE.
XO,
XO,
Please visit my Health and Wellness website 11MLWellness here.